Adding a Run Status Output - Revision history

Thomas Peterson at 14:07, 2 November 2023

2023-11-02T14:07:57Z

← Older revision		Revision as of 14:07, 2 November 2023
Line 21:		Line 21:
	''Custom DO setup on DCT''		''Custom DO setup on DCT''

	On this page select the ON condition (box 2) and set to On when '''RPM''' (under Other category) '''above 500''' or another appropriate value. The Deadband can be set to 0. The on and off delay give the amount of time after the condition is met or not met to change the output, setting each to 10 seconds can help keep the output from going on/off several times around startup or shutdown. The Force off during ESD option isn't relevant.		On this page select the ON condition (box 2) and set to On when '''RPM''' (under Other category) '''above 500''' or another appropriate value. The Deadband can be set to 0. The on and off delay give the amount of time after the condition is met or not met to change the output, setting each to 10 seconds can help keep the output from going on/off several times around startup or shutdown. The "Force off during ESD" option isn't relevant.

	Once configured, select "Submit" on the bottom to save.		Once configured, select "Submit" on the bottom to save.

Thomas Peterson at 14:07, 2 November 2023

2023-11-02T14:07:42Z

← Older revision		Revision as of 14:07, 2 November 2023
Line 3:		Line 3:
	There are two ways to add the output depending on version, detailed below.		There are two ways to add the output depending on version, detailed below.

	'''If the Brain version is at least 2563 and DCT version 1.60'''		'''If the Brain version is at least 2563 and DCT version at least 1.60'''

	For new versions, there is a built in option for run status.		For new versions, there is a built in option for run status.
Line 9:		Line 9:
	Navigate to Settings - Brain - Outputs Setup - Digital Output Function Selection. Select the Digital Out to use for this feature, and scroll to the 4th page of options to select "Run Status". See also [[Annunciator Digital Output Function Selection]].		Navigate to Settings - Brain - Outputs Setup - Digital Output Function Selection. Select the Digital Out to use for this feature, and scroll to the 4th page of options to select "Run Status". See also [[Annunciator Digital Output Function Selection]].

	'''If the Brain or DCT software is older, or ~~for~~ an EIM'''		'''If the Brain or DCT software is older, or if the unit has an EIM'''

	A run status output can be added as a "Custom Digital Out".		A run status output can be added as a "Custom Digital Out".
Line 18:		Line 18:

	[[File:Run status custom do.png]]		[[File:Run status custom do.png]]

	''Custom DO setup on DCT''		''Custom DO setup on DCT''

	On this page select the ON condition (box 2) and set to On when '''RPM''' (under Other category) '''above 500''' or another appropriate value. The Deadband can be set to 0. The on and off delay give the amount of time after the condition is met or not met to change the output, setting each to 10 seconds can help keep the output from going on/off several times around startup or shutdown.		On this page select the ON condition (box 2) and set to On when '''RPM''' (under Other category) '''above 500''' or another appropriate value. The Deadband can be set to 0. The on and off delay give the amount of time after the condition is met or not met to change the output, setting each to 10 seconds can help keep the output from going on/off several times around startup or shutdown. The Force off during ESD option isn't relevant.

	Once configured, select "Submit" on the bottom to save.		Once configured, select "Submit" on the bottom to save.

Thomas Peterson at 14:05, 2 November 2023

2023-11-02T14:05:38Z

← Older revision		Revision as of 14:05, 2 November 2023
Line 3:		Line 3:
	There are two ways to add the output depending on version, detailed below.		There are two ways to add the output depending on version, detailed below.

	''If the Brain version is at least 2563 and DCT version 1.60''		'''If the Brain version is at least 2563 and DCT version 1.60'''

	For new versions, there is a built in option for run status.		For new versions, there is a built in option for run status.

	Navigate to Settings - Brain - ~~Output Setups~~ - Digital Output Function Selection. Select the Digital Out to use for this feature, and scroll to the 4th page of options to select "Run Status". See also [[Annunciator Digital Output Function Selection]].		Navigate to Settings - Brain - Outputs Setup - Digital Output Function Selection. Select the Digital Out to use for this feature, and scroll to the 4th page of options to select "Run Status". See also [[Annunciator Digital Output Function Selection]].

	''If the Brain or DCT software is older, or for an EIM''		'''If the Brain or DCT software is older, or for an EIM'''

			A run status output can be added as a "Custom Digital Out".

			Navigate to Settings - Brain - Outputs Setup - Custom Digital Out.

			On an EIM, navigate to Annunciator - Annunciator Setup - Outputs Setup - Custom Digital Out.

			[[File:Run status custom do.png]]
			''Custom DO setup on DCT''

			On this page select the ON condition (box 2) and set to On when '''RPM''' (under Other category) '''above 500''' or another appropriate value. The Deadband can be set to 0. The on and off delay give the amount of time after the condition is met or not met to change the output, setting each to 10 seconds can help keep the output from going on/off several times around startup or shutdown.

			Once configured, select "Submit" on the bottom to save.

Thomas Peterson: Created page with "A run status output is powered on when the unit is running. It can be used to signal some other PLC or device that the unit is running. There are two ways to add the output depending on version, detailed below. ''If the Brain version is at least 2563 and DCT version 1.60'' For new versions, there is a built in option for run status. Navigate to Settings - Brain - Output Setups - Digital Output Function Selection. Select the Digital Out to use for this feature, and sc..."

2023-11-02T13:57:21Z

Created page with "A run status output is powered on when the unit is running. It can be used to signal some other PLC or device that the unit is running. There are two ways to add the output depending on version, detailed below. ''If the Brain version is at least 2563 and DCT version 1.60'' For new versions, there is a built in option for run status. Navigate to Settings - Brain - Output Setups - Digital Output Function Selection. Select the Digital Out to use for this feature, and sc..."

New page

A run status output is powered on when the unit is running. It can be used to signal some other PLC or device that the unit is running.

There are two ways to add the output depending on version, detailed below.

''If the Brain version is at least 2563 and DCT version 1.60''

For new versions, there is a built in option for run status.

Navigate to Settings - Brain - Output Setups - Digital Output Function Selection. Select the Digital Out to use for this feature, and scroll to the 4th page of options to select "Run Status". See also [[Annunciator Digital Output Function Selection]].

''If the Brain or DCT software is older, or for an EIM''