Annunciator Testing Mode - Revision history

Thomas Peterson at 16:31, 13 July 2023

2023-07-13T16:31:40Z

← Older revision		Revision as of 16:31, 13 July 2023
Line 1:		Line 1:
	The Brain ~~can be used in~~ a test mode ~~with~~ the engine running ~~using the Brain Testing Mode screen~~. This page is accessed from the main setup by going to Brain -> “Testing Mode”.		The Brain has a timed test mode that is used while the engine is running to test faults without shutting down. This page is accessed from the main setup by going to Brain -> “Testing Mode”.

	Note: ~~With~~ the unit not running, inputs can be tested at the [[Annunciator Fault & Output Status Screen]] instead.		Note: If the unit is not running, inputs can be tested at the [[Annunciator Fault & Output Status Screen]] instead.

	[[File:Testing Mode.jpg]]		[[File:Testing Mode.jpg]]
Line 7:		Line 7:
	''Test Mode Page''		''Test Mode Page''

	On the page the testing mode can be started or stopped. When started, the test mode will run for 5 minutes, or until it is stopped. During testing mode the unit will not shut down for any A, B, or C class faults. The faults will still be shown on the Inputs and Timers Status page to verify the ~~shutdown~~ is ~~normally~~ operational. Any ESD class inputs will still cause the engine to be shut down when faulted.		On the page the testing mode can be started or stopped. When started, the test mode will run for 5 minutes, or until it is stopped. During testing mode the unit will not shut down for any A, B, or C class faults. The faults will still be shown on the Inputs and Timers Status page to verify the fault is operational. Any ESD class inputs will still cause the engine to be shut down when faulted.

	Selecting the button "Previous fault times" will go to the Previous Fault Times page, which shows the previous time an input was faulted for any reason, whether in test mode or not.		Selecting the button "Previous fault times" will go to the Previous Fault Times page, which shows the previous time an input was faulted for any reason, whether in test mode or not.

	[[File:Annunciator Fault Event.jpg]]		[[File:Annunciator Fault Event.jpg]]

Thomas Peterson at 21:47, 4 August 2022

2022-08-04T21:47:21Z

← Older revision		Revision as of 21:47, 4 August 2022
Line 1:		Line 1:
	The ~~annunciator~~ can be used in a test mode with ~~or without~~ the engine running using the ~~Annunciator~~ Testing Mode screen ~~(Pg. 662)~~. This page is accessed from the ~~annunciator~~ main setup by ~~selecting~~ “Testing Mode”.		The Brain can be used in a test mode with the engine running using the Brain Testing Mode screen. This page is accessed from the main setup by going to Brain -> “Testing Mode”.

			Note: With the unit not running, inputs can be tested at the [[Annunciator Fault & Output Status Screen]] instead.

	[[File:Testing Mode.jpg]]		[[File:Testing Mode.jpg]]

	''~~Annunciator~~ Test Mode Page''		''Test Mode Page''

	On the page the testing mode can be started or stopped. When started, the test mode will run for 15 minutes, or until it is stopped. During testing mode the ~~annunciator~~ will not shut down ~~the engine~~ for any A, B, or C class faults. The faults will still be shown on the ~~Annunciator~~ Inputs and Timers Status page to verify the shutdown is normally operational. Any ESD class inputs will still cause the engine to be shut down when faulted.		On the page the testing mode can be started or stopped. When started, the test mode will run for 5 minutes, or until it is stopped. During testing mode the unit will not shut down for any A, B, or C class faults. The faults will still be shown on the Inputs and Timers Status page to verify the shutdown is normally operational. Any ESD class inputs will still cause the engine to be shut down when faulted.

	Selecting the button "Previous fault times" will go to the Previous Fault Times page, which shows the previous time an input was faulted for any reason, whether in test mode or not.		Selecting the button "Previous fault times" will go to the Previous Fault Times page, which shows the previous time an input was faulted for any reason, whether in test mode or not.

			[[File:Annunciator Fault Event.jpg]]

Sean Sanders at 18:42, 2 August 2022

2022-08-02T18:42:30Z

← Older revision		Revision as of 18:42, 2 August 2022
Line 1:		Line 1:
	The annunciator can be used in a test mode with or without the engine running using the Annunciator Testing Mode screen (Pg. 662). This page is accessed from the annunciator main setup by selecting “Testing Mode”.		The annunciator can be used in a test mode with or without the engine running using the Annunciator Testing Mode screen (Pg. 662). This page is accessed from the annunciator main setup by selecting “Testing Mode”.

	<nowiki></nowiki>Insert Image		[[File:Testing Mode.jpg]]

	''Annunciator Test Mode Page''		''Annunciator Test Mode Page''

Sean Sanders at 17:40, 2 August 2022

2022-08-02T17:40:47Z

← Older revision		Revision as of 17:40, 2 August 2022
Line 8:		Line 8:

	Selecting the button "Previous fault times" will go to the Previous Fault Times page, which shows the previous time an input was faulted for any reason, whether in test mode or not.		Selecting the button "Previous fault times" will go to the Previous Fault Times page, which shows the previous time an input was faulted for any reason, whether in test mode or not.

	<nowiki></nowiki>Insert Image

Sean Sanders: Created page with "The annunciator can be used in a test mode with or without the engine running using the Annunciator Testing Mode screen (Pg. 662). This page is accessed from the annunciator main setup by selecting “Testing Mode”. Insert Image ''Annunciator Test Mode Page'' On the page the testing mode can be started or stopped. When started, the test mode will run for 15 minutes, or until it is stopped. During testing mode the annunciator will not shut down th..."

2022-07-21T21:17:51Z

Created page with "The annunciator can be used in a test mode with or without the engine running using the Annunciator Testing Mode screen (Pg. 662). This page is accessed from the annunciator main setup by selecting “Testing Mode”. <nowiki>*</nowiki>Insert Image* ''Annunciator Test Mode Page'' On the page the testing mode can be started or stopped. When started, the test mode will run for 15 minutes, or until it is stopped. During testing mode the annunciator will not shut down th..."

New page

The annunciator can be used in a test mode with or without the engine running using the Annunciator Testing Mode screen (Pg. 662). This page is accessed from the annunciator main setup by selecting “Testing Mode”.

<nowiki>*</nowiki>Insert Image*

''Annunciator Test Mode Page''

On the page the testing mode can be started or stopped. When started, the test mode will run for 15 minutes, or until it is stopped. During testing mode the annunciator will not shut down the engine for any A, B, or C class faults. The faults will still be shown on the Annunciator Inputs and Timers Status page to verify the shutdown is normally operational. Any ESD class inputs will still cause the engine to be shut down when faulted.

Selecting the button "Previous fault times" will go to the Previous Fault Times page, which shows the previous time an input was faulted for any reason, whether in test mode or not.

<nowiki>*</nowiki>Insert Image*