Back Activation - Revision history

Thomas Peterson: /* DCT Procedure */

2024-06-06T13:27:03Z

DCT Procedure

← Older revision		Revision as of 13:27, 6 June 2024
Line 11:		Line 11:
	2. Navigate to Settings -> System / Global Settings		2. Navigate to Settings -> System / Global Settings

	[[File:DCT Settings Ssytem.png]]		[[File:DCT Settings Ssytem.png\|600px]]

	3. Go to "Page Down" then "Telematics Settings"		3. Go to "Page Down" then "Telematics Settings"

	[[File:System tel.png]]		[[File:System tel.png\|400px]]

	4. Hit "Select Test..." button, then "Request Service Level Update"		4. Hit "Select Test..." button, then "Request Service Level Update"

	[[File:Svc update.png]]		[[File:Svc update.png\|700px]]

	==EDR Procedure==		==EDR Procedure==

Thomas Peterson at 13:26, 6 June 2024

2024-06-06T13:26:19Z

← Older revision		Revision as of 13:26, 6 June 2024
Line 1:		Line 1:
	In most cases when a device is activated a message is sent from the server to the device telling it to change its send settings. In some cases ~~though~~ the message can't be sent at the time, and a manual step is needed top pull the setting update in the other direction. An example case would be where a unit is set to active before the panel is powered up, and later it is powered and needs to be activated.		In most cases when a device is activated a message is sent from the server to the device telling it to change its send settings. However, in some cases the message can't be sent at the time, and a manual step is needed top pull the setting update in the other direction. An example case would be where a unit is set to active before the panel is powered up, and later it is powered and needs to be activated.

	The following shows how to request a service level update on a DCT and EDR. Note that this assumes EMIT already set the service level to active.		The following shows how to request a service level update on a DCT and EDR. Note that this assumes EMIT already set the service level to active.

Thomas Peterson: Created page with "In most cases when a device is activated a message is sent from the server to the device telling it to change its send settings. In some cases though the message can't be sent at the time, and a manual step is needed top pull the setting update in the other direction. An example case would be where a unit is set to active before the panel is powered up, and later it is powered and needs to be activated. The following shows how to request a service level update on a DCT..."

2024-06-06T13:25:48Z

Created page with "In most cases when a device is activated a message is sent from the server to the device telling it to change its send settings. In some cases though the message can't be sent at the time, and a manual step is needed top pull the setting update in the other direction. An example case would be where a unit is set to active before the panel is powered up, and later it is powered and needs to be activated. The following shows how to request a service level update on a DCT..."

New page

In most cases when a device is activated a message is sent from the server to the device telling it to change its send settings. In some cases though the message can't be sent at the time, and a manual step is needed top pull the setting update in the other direction. An example case would be where a unit is set to active before the panel is powered up, and later it is powered and needs to be activated.

The following shows how to request a service level update on a DCT and EDR. Note that this assumes EMIT already set the service level to active.

==DCT Procedure==

0. If the DCT is not showing a cell connection, power cycle and wait a few minutes for signal strength to show up

1. Enter Setup or Engineering password

2. Navigate to Settings -> System / Global Settings

[[File:DCT Settings Ssytem.png]]

3. Go to "Page Down" then "Telematics Settings"

[[File:System tel.png]]

4. Hit "Select Test..." button, then "Request Service Level Update"

[[File:Svc update.png]]

==EDR Procedure==

0. Connect to the EDR wifi console. See [[EDR_Wi-Fi_Console#Connecting]]

1. Along the top of the page or on the top main menu go to the "Debug" page

[[File:Edr debug.png]]

2. Open the "Device Config" dropdown and select "Sync Telematics Config"

[[File:Edr sync.png]]