DCT Password Levels - Revision history

Thomas Peterson at 17:51, 17 February 2023

2023-02-17T17:51:24Z

← Older revision		Revision as of 17:51, 17 February 2023
Line 1:		Line 1:
	The DCT has three password levels: read-only, Setup, and Engineering. The list below shows which settings groups are included under each level.		The DCT has three password levels: read-only, Setup, and Engineering. The list below shows which settings groups are included under each level.

			The passwords can be changed under System Settings - Change Passwords. See [[DCT_System_Settings_or_Utilities#Change_Passwords\|this link]] for details.

			Optionally, the Engineering level can be locked out to require a USB security key. See [[EIM_Security_Key]]

	Note: some uncommon settings are not shown		Note: some uncommon settings are not shown

Thomas Peterson: /* Settings that can be changed under Engineering */

2023-02-06T21:50:20Z

Settings that can be changed under Engineering

← Older revision		Revision as of 21:50, 6 February 2023
Line 36:		Line 36:
	==Settings that can be changed under Engineering==		==Settings that can be changed under Engineering==

	~~Everything else~~		All settings can be changed under engineering. Summary of items not above:

			*Analog input sensor settings
			*PID loop detailed settings
			*Recycle loop detailed settings
			*Crank setup
			*Bypass and blowdown settings
			*Start permissive
			*Input calibrations
			*Purge settings
			*Remote switch setup
			*Screw load settings
			*Valve setup
			*EMIT Ignition main setup and engineering setup
			*EMIT Speed controller main setup, engineering setup, pid setup

Thomas Peterson at 21:45, 6 February 2023

2023-02-06T21:45:34Z

← Older revision		Revision as of 21:45, 6 February 2023
Line 1:		Line 1:
	The DCT has three password levels: read-only, Setup, and Engineering. The list below shows which settings groups are included under each level.		The DCT has three password levels: read-only, Setup, and Engineering. The list below shows which settings groups are included under each level.

			Note: some uncommon settings are not shown

	==Settings that can be changed under read-only==		==Settings that can be changed under read-only==

Thomas Peterson at 21:45, 6 February 2023

2023-02-06T21:45:09Z

← Older revision		Revision as of 21:45, 6 February 2023
Line 11:		Line 11:
	*AFRC Alarms		*AFRC Alarms
	*Analog input kills (but not sensor settings)		*Analog input kills (but not sensor settings)
			*Digital input setup
	*B timer lengths		*B timer lengths
	*Buzzer alarm		*Buzzer alarm
	*Custom digital output criteria		*Custom digital output criteria
			*Brain ECU selection
			*Gauge setup
			*Idle hold settings
			*Speed alarms
			*Load delay settings
			*Pre/Post lube settings
			*Noflow settings
			*Recycle loop settings (some settings)
			*Speed de-rate settings
			*Start gas settings
			*Thermocouple input kills
			*EMIT Ignition alarms, calibration, timing setup
			*EMIT Speed controller Alarm setup, idle hold setup, sensor setup, calibration
			*EMIT Vibration sensor kill level

Thomas Peterson: Created page with "The DCT has three password levels: read-only, Setup, and Engineering. The list below shows which settings groups are included under each level. ==Settings that can be changed under read-only== PID Setpoint/Deadband (if enabled on PID setup page) Speed setpoint ==Settings that can be changed under Setup== Engine hour timers reset AFRC Alarms Analog input kills (but not sensor settings) B timer lengths Buzzer alarm Custom digital output criteria ==Settings t..."

2023-02-06T21:39:15Z

Created page with "The DCT has three password levels: read-only, Setup, and Engineering. The list below shows which settings groups are included under each level. ==Settings that can be changed under read-only== *PID Setpoint/Deadband (if enabled on PID setup page) *Speed setpoint ==Settings that can be changed under Setup== *Engine hour timers reset *AFRC Alarms *Analog input kills (but not sensor settings) *B timer lengths *Buzzer alarm *Custom digital output criteria ==Settings t..."

New page

The DCT has three password levels: read-only, Setup, and Engineering. The list below shows which settings groups are included under each level.

==Settings that can be changed under read-only==

*PID Setpoint/Deadband (if enabled on PID setup page)
*Speed setpoint

==Settings that can be changed under Setup==

*Engine hour timers reset
*AFRC Alarms
*Analog input kills (but not sensor settings)
*B timer lengths
*Buzzer alarm
*Custom digital output criteria

==Settings that can be changed under Engineering==

Everything else