Speed Modes Of Operation - Revision history

Thomas Peterson at 21:43, 29 July 2022

2022-07-29T21:43:03Z

← Older revision		Revision as of 21:43, 29 July 2022
Line 1:		Line 1:
	The user can select through the panel’s mode switch either “Idle,” “Manual,” or “Auto” (Run) mode for the Governor. Additionally, Auto mode can be setup to function in various ways. A description of each control mode is provided below.		The user can select through the panel’s mode switch either “Idle,” “Manual,” or “Auto” (Run) mode for the Governor. Additionally, Auto mode can be setup to function in various ways. A description of each control mode is provided below.

	=== ~~IDLE~~ ===		=== Idle ===
	When the panel’s mode switch is in Idle, the Governor will hold the engine at the user-specified idle speed. This speed is specified during governor setup, described on another page. Note that the engine might be forced to run idle speed during an idle hold condition even if the switch is not in the idle position.		When the panel’s mode switch is in Idle, the Governor will hold the engine at the user-specified idle speed. This speed is specified during governor setup, described on another page. Note that the engine might be forced to run idle speed during an idle hold condition even if the switch is not in the idle position.

	=== ~~MANUAL~~ ===		=== Manual ===
	When the panel’s mode switch is in Manual the Governor will hold at a fixed manual speed. Whenever the switch is switched to Manual, the manual speed will start at whatever speed the engine is currently operating at and from there the user can use the panel’s speed switch to increase or decrease the speed. This mode is intended to be used only temporarily.		When the panel’s mode switch is in Manual the Governor will hold at a fixed manual speed. Whenever the switch is switched to Manual, the manual speed will start at whatever speed the engine is currently operating at and from there the user can use the panel’s speed switch to increase or decrease the speed. This mode is intended to be used only temporarily.

Line 11:		Line 11:
	Note: If the mode switch is not at Manual, then the “Speed+ / Speed-” speed switch will have no effect.		Note: If the mode switch is not at Manual, then the “Speed+ / Speed-” speed switch will have no effect.

	=== ~~AUTO~~ ===		=== Auto ===
	The Auto setting is used for normal run operation of the engine. The behavior of the Governor in the Auto setting can currently be set to one of three ways, described below.		The Auto setting is used for normal run operation of the engine. The behavior of the Governor in the Auto setting can currently be set to one of three ways, described below.

	Note: When switching between operating modes (Idle, Manual, or Auto), the Governor will ramp more slowly than it would during normal operation.		Note: When switching between operating modes (Idle, Manual, or Auto), the Governor will ramp more slowly than it would during normal operation.

	==== ~~AUTO~~ – ~~CONTROL TO FIXED SPEED~~ ====		==== Auto – Control to Fixed Speed ====
	For a fixed speed setpoint, the Governor will hold the engine at a specified run speed. This run speed can be adjusted in governor setup.		For a fixed speed setpoint, the Governor will hold the engine at a specified run speed. This run speed can be adjusted in governor setup.

	==== ~~AUTO~~ – ~~CONTROL TO SUCTION PRESSURE~~ ====		==== Auto – Control to Suction Pressure ====
	For a suction pressure setpoint, the engine will increase speed when the suction pressure is too high and decrease speed when the suction pressure is too low. The user specifies some operating range for RPMs during this mode. This mode is useful for cases where the incoming pressure varies, such as a low-producing well. Decreasing the RPM when the pressure drops gives the supply a chance to replenish. This can result considerable fuel savings and reduction of engine wear by eliminating wasted work by the engine.		For a suction pressure setpoint, the engine will increase speed when the suction pressure is too high and decrease speed when the suction pressure is too low. The user specifies some operating range for RPMs during this mode. This mode is useful for cases where the incoming pressure varies, such as a low-producing well. Decreasing the RPM when the pressure drops gives the supply a chance to replenish. This can result considerable fuel savings and reduction of engine wear by eliminating wasted work by the engine.

	==== ~~AUTO~~ – ~~CONTROL TO DISCHARGE PRESSURE~~ ====		==== Auto – Control to Discharge Pressure ====
	For a discharge pressure setpoint, the engine will increase speed when the discharge pressure is too low and decrease speed when the discharge pressure is too high. Overall, this keeps the discharge at a constant rate. This mode can be used when the supply pressure is unconstrained, but the outgoing pressure is desired to be constant.		For a discharge pressure setpoint, the engine will increase speed when the discharge pressure is too low and decrease speed when the discharge pressure is too high. Overall, this keeps the discharge at a constant rate. This mode can be used when the supply pressure is unconstrained, but the outgoing pressure is desired to be constant.

Thomas Peterson at 21:42, 29 July 2022

2022-07-29T21:42:07Z

← Older revision		Revision as of 21:42, 29 July 2022
Line 2:		Line 2:

	=== IDLE ===		=== IDLE ===
	When the panel’s mode switch is in Idle, the Governor will hold the engine at the user-specified idle speed. This speed is specified during governor setup, described in ~~a later section~~.		When the panel’s mode switch is in Idle, the Governor will hold the engine at the user-specified idle speed. This speed is specified during governor setup, described on another page. Note that the engine might be forced to run idle speed during an idle hold condition even if the switch is not in the idle position.

	=== MANUAL ===		=== MANUAL ===
	When the panel’s mode switch is in Manual, the Governor will hold at a fixed manual speed. Whenever the switch is switched to Manual, the manual speed will start at whatever speed the engine is currently operating at and from there, the user can use the panel’s speed switch to increase or decrease the speed. This mode is intended to be used only temporarily.		When the panel’s mode switch is in Manual the Governor will hold at a fixed manual speed. Whenever the switch is switched to Manual, the manual speed will start at whatever speed the engine is currently operating at and from there the user can use the panel’s speed switch to increase or decrease the speed. This mode is intended to be used only temporarily.

	Note: If the mode switch is in Manual when the engine is started, the manual speed will start at the idle speed.		Note: If the mode switch is in Manual when the engine is started, the manual speed will start at the idle speed.
Line 20:		Line 20:

	==== AUTO – CONTROL TO SUCTION PRESSURE ====		==== AUTO – CONTROL TO SUCTION PRESSURE ====
	For a suction pressure setpoint, the engine will increase speed when the suction pressure is too high and decrease speed when the suction pressure is too low. The user specifies some range ~~that the Governor should not deviate from~~ during ~~the Auto operation~~. This mode is useful for cases where the incoming pressure varies, such as a low-producing well. Decreasing the RPM when the pressure drops gives the supply a chance to replenish. This can result considerable fuel savings and reduction of engine wear by eliminating wasted work by the engine.		For a suction pressure setpoint, the engine will increase speed when the suction pressure is too high and decrease speed when the suction pressure is too low. The user specifies some operating range for RPMs during this mode. This mode is useful for cases where the incoming pressure varies, such as a low-producing well. Decreasing the RPM when the pressure drops gives the supply a chance to replenish. This can result considerable fuel savings and reduction of engine wear by eliminating wasted work by the engine.

	==== AUTO – CONTROL TO DISCHARGE PRESSURE ====		==== AUTO – CONTROL TO DISCHARGE PRESSURE ====
	For a discharge pressure setpoint, the engine will increase speed when the discharge pressure is too low and decrease speed when the discharge pressure is too high. Overall, this keeps the discharge at a constant rate. This mode can be used when the supply pressure is unconstrained, but the outgoing pressure is desired to be constant.		For a discharge pressure setpoint, the engine will increase speed when the discharge pressure is too low and decrease speed when the discharge pressure is too high. Overall, this keeps the discharge at a constant rate. This mode can be used when the supply pressure is unconstrained, but the outgoing pressure is desired to be constant.

Thomas Peterson at 21:38, 29 July 2022

2022-07-29T21:38:56Z

Sean Sanders: Sean Sanders moved page Modes Of Operation to Speed Modes Of Operation

2022-07-26T18:57:55Z

Sean Sanders moved page Modes Of Operation to Speed Modes Of Operation

← Older revision	Revision as of 18:57, 26 July 2022
(No difference)

Sean Sanders: Created page with "=== Modes Of Operation === The user can select through the panel’s mode switch either “Idle,” “Manual,” or “Auto” (Run) mode for the Governor. Additionally, Auto mode can be setup to function in various ways. A description of each control mode is provided below. ==== IDLE ==== When the panel’s mode switch is in Idle, the Governor will hold the engine at the user-specified idle speed. This speed is specified during governor setup, described in a later sec..."

2022-07-21T17:43:48Z

Created page with "=== Modes Of Operation === The user can select through the panel’s mode switch either “Idle,” “Manual,” or “Auto” (Run) mode for the Governor. Additionally, Auto mode can be setup to function in various ways. A description of each control mode is provided below. ==== IDLE ==== When the panel’s mode switch is in Idle, the Governor will hold the engine at the user-specified idle speed. This speed is specified during governor setup, described in a later sec..."

New page

=== Modes Of Operation ===
The user can select through the panel’s mode switch either “Idle,” “Manual,” or “Auto” (Run) mode for the Governor. Additionally, Auto mode can be setup to function in various ways. A description of each control mode is provided below.

==== IDLE ====
When the panel’s mode switch is in Idle, the Governor will hold the engine at the user-specified idle speed. This speed is specified during governor setup, described in a later section.

==== MANUAL ====
When the panel’s mode switch is in Manual, the Governor will hold at a fixed manual speed. Whenever the switch is switched to Manual, the manual speed will start at whatever speed the engine is currently operating at and from there, the user can use the panel’s speed switch to increase or decrease the speed. This mode is intended to be used only temporarily.

Note: If the mode switch is in Manual when the engine is started, the manual speed will start at the idle speed.

Note: If the mode switch is not at Manual, then the “Speed+ / Speed-” speed switch will have no effect.

==== AUTO ====
The Auto setting is used for normal run operation of the engine. The behavior of the Governor in the Auto setting can currently be set to one of three ways, described below.

Note: When switching between operating modes (Idle, Manual, or Auto), the Governor will ramp more slowly than it would during normal operation.

===== AUTO – CONTROL TO FIXED SPEED =====
For a fixed speed setpoint, the Governor will hold the engine at a specified run speed. This run speed can be adjusted in governor setup.

===== AUTO – CONTROL TO SUCTION PRESSURE =====
For a suction pressure setpoint, the engine will increase speed when the suction pressure is too high and decrease speed when the suction pressure is too low. The user specifies some range that the Governor should not deviate from during the Auto operation. This mode is useful for cases where the incoming pressure varies, such as a low-producing well. Decreasing the RPM when the pressure drops gives the supply a chance to replenish. This can result considerable fuel savings and reduction of engine wear by eliminating wasted work by the engine.

===== AUTO – CONTROL TO DISCHARGE PRESSURE =====
For a discharge pressure setpoint, the engine will increase speed when the discharge pressure is too low and decrease speed when the discharge pressure is too high. Overall, this keeps the discharge at a constant rate. This mode can be used when the supply pressure is unconstrained, but the outgoing pressure is desired to be constant.

← Older revision		Revision as of 21:38, 29 July 2022
Line 1:		Line 1:
	~~=== Modes Of Operation ===~~
	The user can select through the panel’s mode switch either “Idle,” “Manual,” or “Auto” (Run) mode for the Governor. Additionally, Auto mode can be setup to function in various ways. A description of each control mode is provided below.		The user can select through the panel’s mode switch either “Idle,” “Manual,” or “Auto” (Run) mode for the Governor. Additionally, Auto mode can be setup to function in various ways. A description of each control mode is provided below.

	==== IDLE ====		=== IDLE ===
	When the panel’s mode switch is in Idle, the Governor will hold the engine at the user-specified idle speed. This speed is specified during governor setup, described in a later section.		When the panel’s mode switch is in Idle, the Governor will hold the engine at the user-specified idle speed. This speed is specified during governor setup, described in a later section.

	==== MANUAL ====		=== MANUAL ===
	When the panel’s mode switch is in Manual, the Governor will hold at a fixed manual speed. Whenever the switch is switched to Manual, the manual speed will start at whatever speed the engine is currently operating at and from there, the user can use the panel’s speed switch to increase or decrease the speed. This mode is intended to be used only temporarily.		When the panel’s mode switch is in Manual, the Governor will hold at a fixed manual speed. Whenever the switch is switched to Manual, the manual speed will start at whatever speed the engine is currently operating at and from there, the user can use the panel’s speed switch to increase or decrease the speed. This mode is intended to be used only temporarily.

Line 12:		Line 11:
	Note: If the mode switch is not at Manual, then the “Speed+ / Speed-” speed switch will have no effect.		Note: If the mode switch is not at Manual, then the “Speed+ / Speed-” speed switch will have no effect.

	==== AUTO ====		=== AUTO ===
	The Auto setting is used for normal run operation of the engine. The behavior of the Governor in the Auto setting can currently be set to one of three ways, described below.		The Auto setting is used for normal run operation of the engine. The behavior of the Governor in the Auto setting can currently be set to one of three ways, described below.

	Note: When switching between operating modes (Idle, Manual, or Auto), the Governor will ramp more slowly than it would during normal operation.		Note: When switching between operating modes (Idle, Manual, or Auto), the Governor will ramp more slowly than it would during normal operation.

	===== AUTO – CONTROL TO FIXED SPEED =====		==== AUTO – CONTROL TO FIXED SPEED ====
	For a fixed speed setpoint, the Governor will hold the engine at a specified run speed. This run speed can be adjusted in governor setup.		For a fixed speed setpoint, the Governor will hold the engine at a specified run speed. This run speed can be adjusted in governor setup.

	===== AUTO – CONTROL TO SUCTION PRESSURE =====		==== AUTO – CONTROL TO SUCTION PRESSURE ====
	For a suction pressure setpoint, the engine will increase speed when the suction pressure is too high and decrease speed when the suction pressure is too low. The user specifies some range that the Governor should not deviate from during the Auto operation. This mode is useful for cases where the incoming pressure varies, such as a low-producing well. Decreasing the RPM when the pressure drops gives the supply a chance to replenish. This can result considerable fuel savings and reduction of engine wear by eliminating wasted work by the engine.		For a suction pressure setpoint, the engine will increase speed when the suction pressure is too high and decrease speed when the suction pressure is too low. The user specifies some range that the Governor should not deviate from during the Auto operation. This mode is useful for cases where the incoming pressure varies, such as a low-producing well. Decreasing the RPM when the pressure drops gives the supply a chance to replenish. This can result considerable fuel savings and reduction of engine wear by eliminating wasted work by the engine.

	===== AUTO – CONTROL TO DISCHARGE PRESSURE =====		==== AUTO – CONTROL TO DISCHARGE PRESSURE ====
	For a discharge pressure setpoint, the engine will increase speed when the discharge pressure is too low and decrease speed when the discharge pressure is too high. Overall, this keeps the discharge at a constant rate. This mode can be used when the supply pressure is unconstrained, but the outgoing pressure is desired to be constant.		For a discharge pressure setpoint, the engine will increase speed when the discharge pressure is too low and decrease speed when the discharge pressure is too high. Overall, this keeps the discharge at a constant rate. This mode can be used when the supply pressure is unconstrained, but the outgoing pressure is desired to be constant.