DCT Password Levels: Difference between revisions

From EMIT Controls
(Created page with "The DCT has three password levels: read-only, Setup, and Engineering. The list below shows which settings groups are included under each level. ==Settings that can be changed under read-only== *PID Setpoint/Deadband (if enabled on PID setup page) *Speed setpoint ==Settings that can be changed under Setup== *Engine hour timers reset *AFRC Alarms *Analog input kills (but not sensor settings) *B timer lengths *Buzzer alarm *Custom digital output criteria ==Settings t...")
 
No edit summary
 
(3 intermediate revisions by the same user not shown)
Line 1: Line 1:
The DCT has three password levels: read-only, Setup, and Engineering. The list below shows which settings groups are included under each level.
The DCT has three password levels: read-only, Setup, and Engineering. The list below shows which settings groups are included under each level.
The passwords can be changed under System Settings - Change Passwords. See [[DCT_System_Settings_or_Utilities#Change_Passwords|this link]] for details.
Optionally, the Engineering level can be locked out to require a USB security key. See [[EIM_Security_Key]]
Note: some uncommon settings are not shown


==Settings that can be changed under read-only==
==Settings that can be changed under read-only==
Line 11: Line 17:
*AFRC Alarms
*AFRC Alarms
*Analog input kills (but not sensor settings)
*Analog input kills (but not sensor settings)
*Digital input setup
*B timer lengths
*B timer lengths
*Buzzer alarm
*Buzzer alarm
*Custom digital output criteria
*Custom digital output criteria
*Brain ECU selection
*Gauge setup
*Idle hold settings
*Speed alarms
*Load delay settings
*Pre/Post lube settings
*Noflow settings
*Recycle loop settings (some settings)
*Speed de-rate settings
*Start gas settings
*Thermocouple input kills
*EMIT Ignition alarms, calibration, timing setup
*EMIT Speed controller Alarm setup, idle hold setup, sensor setup, calibration
*EMIT Vibration sensor kill level




Line 19: Line 40:
==Settings that can be changed under Engineering==
==Settings that can be changed under Engineering==


Everything else
All settings can be changed under engineering. Summary of items not above:
 
*Analog input sensor settings
*PID loop detailed settings
*Recycle loop detailed settings
*Crank setup
*Bypass and blowdown settings
*Start permissive
*Input calibrations
*Purge settings
*Remote switch setup
*Screw load settings
*Valve setup
*EMIT Ignition main setup and engineering setup
*EMIT Speed controller main setup, engineering setup, pid setup

Latest revision as of 17:51, 17 February 2023

The DCT has three password levels: read-only, Setup, and Engineering. The list below shows which settings groups are included under each level.

The passwords can be changed under System Settings - Change Passwords. See this link for details.

Optionally, the Engineering level can be locked out to require a USB security key. See EIM_Security_Key

Note: some uncommon settings are not shown

Settings that can be changed under read-only

  • PID Setpoint/Deadband (if enabled on PID setup page)
  • Speed setpoint

Settings that can be changed under Setup

  • Engine hour timers reset
  • AFRC Alarms
  • Analog input kills (but not sensor settings)
  • Digital input setup
  • B timer lengths
  • Buzzer alarm
  • Custom digital output criteria
  • Brain ECU selection
  • Gauge setup
  • Idle hold settings
  • Speed alarms
  • Load delay settings
  • Pre/Post lube settings
  • Noflow settings
  • Recycle loop settings (some settings)
  • Speed de-rate settings
  • Start gas settings
  • Thermocouple input kills
  • EMIT Ignition alarms, calibration, timing setup
  • EMIT Speed controller Alarm setup, idle hold setup, sensor setup, calibration
  • EMIT Vibration sensor kill level


Settings that can be changed under Engineering

All settings can be changed under engineering. Summary of items not above:

  • Analog input sensor settings
  • PID loop detailed settings
  • Recycle loop detailed settings
  • Crank setup
  • Bypass and blowdown settings
  • Start permissive
  • Input calibrations
  • Purge settings
  • Remote switch setup
  • Screw load settings
  • Valve setup
  • EMIT Ignition main setup and engineering setup
  • EMIT Speed controller main setup, engineering setup, pid setup