DCT Software Update: Difference between revisions

From EMIT Controls
(Created page with "The DCT can have its software updated using a USB drive. To update the software, follow these steps. * Obtain a software update from this location by selecting the latest "DCT_update..." file. Software Updates * Download the file * Insert a USB drive into the computer * Drag the file from the 'Downloads' folder into the USB drive * Eject the drive, then insert into back of screen * Enter the engineering password on the screen * Navigate to "Settings" -> "System Settings...")
 
No edit summary
Line 1: Line 1:
The DCT can have its software updated using a USB drive. To update the software, follow these steps.
Video available for this topic: https://www.youtube.com/watch?v=o9Mf76GIxBA
*Using a Windows-based computer, transfer the EMIT-provided EIM software update file to a FAT-formatted USB thumb drive
*The file name should be “EIM_update.tar”
*Plug the USB thumb drive into the USB A port on the opposite side of the EIM


* Obtain a software update from this location by selecting the latest "DCT_update..." file. Software Updates
*Within the EIM’s user interface, enter the appropriate password to for either Setup or Engineering security access
* Download the file
*From the System Menu screen (Pg. 0), navigate to the Software Update screen (Pg. 3) by selecting "System Settings / Utilities" then “Software Update”
* Insert a USB drive into the computer
*If the USB drive is plugged in and detected, the screen will be displayed as shown below
* Drag the file from the 'Downloads' folder into the USB drive
*Select the “Start Update“ button to begin the update
* Eject the drive, then insert into back of screen
*The update will take 20-30 seconds and then will restart the EIM, when complete
* Enter the engineering password on the screen
*After the update, the EIM will restart
* Navigate to "Settings" -> "System Settings" -> "Software Update"\
*Remove the USB drive when completed
<nowiki>*</nowiki>Insert Image*


<nowiki>*</nowiki>Add image to go along with software update*
Note: If after the update the EIM application closes but doesn't restart within 30 seconds, it is because the application handler was updated. Turn power on the EIM off and on to finish the update in this case.
 
* Select 'Start Update'
* After about 20 seconds the update should be complete and the screen will restart
 
Note: After update, the engineering password will change. Add the difference in version to the old engineering password. E.g. if updating from 1.12 to 1.18, add '6' to the old engineering password.
 
=== Troubleshooting ===
If the DCT fails to update, try these troubleshooting steps.
 
* Download the file again and verify that the size of the file is similar to what is reported on the software update website
* Make sure the file is in the root directory of the USB drive (not in some sub folder)
* The drive may need to be reformatted. This can be done on the screen itself under "Settings" -> "System / Global Settings" -> "Format USB drive". THIS WILL DELETE ALL FILES ON THE DISK. Afterwards, the file can be recopied onto the drive and the update attempted again.

Revision as of 16:53, 21 July 2022

Video available for this topic: https://www.youtube.com/watch?v=o9Mf76GIxBA

  • Using a Windows-based computer, transfer the EMIT-provided EIM software update file to a FAT-formatted USB thumb drive
  • The file name should be “EIM_update.tar”
  • Plug the USB thumb drive into the USB A port on the opposite side of the EIM
  • Within the EIM’s user interface, enter the appropriate password to for either Setup or Engineering security access
  • From the System Menu screen (Pg. 0), navigate to the Software Update screen (Pg. 3) by selecting "System Settings / Utilities" then “Software Update”
  • If the USB drive is plugged in and detected, the screen will be displayed as shown below
  • Select the “Start Update“ button to begin the update
  • The update will take 20-30 seconds and then will restart the EIM, when complete
  • After the update, the EIM will restart
  • Remove the USB drive when completed

*Insert Image*

Note: If after the update the EIM application closes but doesn't restart within 30 seconds, it is because the application handler was updated. Turn power on the EIM off and on to finish the update in this case.

Retrieved from "http://data.emittechnologies.com/wiki/index.php?title=DCT_Software_Update&oldid=149"