DCT System Settings or Utilities: Difference between revisions

From EMIT Controls
(Created page with "The DCT System Settings / Utilities page is reached by navigating to "Settings" -> "System Settings / Utilities". It contains some settings pages and other pages for items that are related to the screen directly or multiple modules. This document describes each sub-page. ==Software Update== See DCT Software Update ==Display Settings== This screen is used to change the screen brightness. Note that higher brightness creates more heat. ==Go to Page== This screen i...")
 
No edit summary
Line 22: Line 22:


==Compressor Quick Setup==
==Compressor Quick Setup==
This wizard guides through the process of initially setting up the Brain module. This can be used on install to save time in entering settings.
[[File:CompressorQuickSetup.png|600px]]
*Slide 1: Select the number of stages and cylinders for the compressor
*Slide 2: Select the high pressure sensor range for each process stage
*Slide 3: Select which other sensors are used
*Slide 4: Review and save if needed
The compressor quick setup will overwrite many Brain (Annunciator) settings with the new sensor settings. This is intended to be used only once on initial install.


==Engine Timers==
==Engine Timers==
See [[DCT Engine Timers]]


==Modbus Setup==
==Modbus Setup==
See [[DCT Modbus]]


==Ethernet Setup==
==Ethernet Setup==
[[File:EthernetSetup.png|600px]]
The Ethernet setup page is used to setup the IP address settings of the Ethernet port. Select DHCP to automatically get an address, or Static to manually specify an address. The Modbus TCP port number can also be specified on this page.
After changing an address, it is a good idea to wait about 1 minute then cycle power on the screen to make sure that the new settings are used properly.
The "Enable VNC" setting can be used to turn on VNC (similar to remote desktop) for the screen, so that a site level computer can view the screen.
'''Note:''' If using the common 192.168.0.xxx subnet, be sure to change the WiFi IP address, mentioned below.


==Change Setup Password==
==Change Setup Password==
This page can be used to change the ‘Setup’ password.


==Telematics Settings==
==Telematics Settings==
See [[DCT Telematics Setup and Screens#Setup]]


==Format USB Drive==
==Format USB Drive==
See [[DCT USB Format Tool]]


==Wifi Setup==
==Wifi Setup==
The WiFi setup is used to change the IP address used by the WiFi port, which is needed if you need to set the wired ethernet port to 192.168.0.xxx since by default the Wifi is at 192.168.0.1 and the addresses would collide. In this case, simply change the WiFi IP to some other subnet, for example: 192.168.4.1 .
This page can also be used to turn off wifi for the screen.


==ASC Setup==
==ASC Setup==
This page is used to setup the link between the screen and the Ariel Smart Compressor.

Revision as of 17:43, 8 August 2022

The DCT System Settings / Utilities page is reached by navigating to "Settings" -> "System Settings / Utilities". It contains some settings pages and other pages for items that are related to the screen directly or multiple modules. This document describes each sub-page.

Software Update

See DCT Software Update

Display Settings

This screen is used to change the screen brightness. Note that higher brightness creates more heat.

Go to Page

This screen is used to jump to a specific page by the page number. There are a few debug pages that are only accessed by page number.

Engine Quick Setup

This screen is used to pre-fill many settings for the AFR, Speed controller, and Ignition with default settings for a particular engine. This will overwrite many settings for those modules, so it is intended to be used only on a new install.

EngineQuickSetup.raw.png

To use, select the number of cylinders at the top of the screen, then select the engine in the list. The system will overwrite with default settings for that engine to the AFR, Ignition, and Speed controller.

Compressor Quick Setup

This wizard guides through the process of initially setting up the Brain module. This can be used on install to save time in entering settings.

CompressorQuickSetup.png

  • Slide 1: Select the number of stages and cylinders for the compressor
  • Slide 2: Select the high pressure sensor range for each process stage
  • Slide 3: Select which other sensors are used
  • Slide 4: Review and save if needed

The compressor quick setup will overwrite many Brain (Annunciator) settings with the new sensor settings. This is intended to be used only once on initial install.

Engine Timers

See DCT Engine Timers

Modbus Setup

See DCT Modbus

Ethernet Setup

EthernetSetup.png

The Ethernet setup page is used to setup the IP address settings of the Ethernet port. Select DHCP to automatically get an address, or Static to manually specify an address. The Modbus TCP port number can also be specified on this page.

After changing an address, it is a good idea to wait about 1 minute then cycle power on the screen to make sure that the new settings are used properly.

The "Enable VNC" setting can be used to turn on VNC (similar to remote desktop) for the screen, so that a site level computer can view the screen.

Note: If using the common 192.168.0.xxx subnet, be sure to change the WiFi IP address, mentioned below.

Change Setup Password

This page can be used to change the ‘Setup’ password.

Telematics Settings

See DCT Telematics Setup and Screens#Setup

Format USB Drive

See DCT USB Format Tool

Wifi Setup

The WiFi setup is used to change the IP address used by the WiFi port, which is needed if you need to set the wired ethernet port to 192.168.0.xxx since by default the Wifi is at 192.168.0.1 and the addresses would collide. In this case, simply change the WiFi IP to some other subnet, for example: 192.168.4.1 .

This page can also be used to turn off wifi for the screen.

ASC Setup

This page is used to setup the link between the screen and the Ariel Smart Compressor.