All public logs
From EMIT Controls
Combined display of all available logs of EMIT Controls. You can narrow down the view by selecting a log type, the username (case-sensitive), or the affected page (also case-sensitive).
(newest | oldest) View (newer 50 | older 50) (20 | 50 | 100 | 250 | 500)- 18:42, 30 July 2024 Thomas Peterson talk contribs created page File:Test msg list.png
- 18:42, 30 July 2024 Thomas Peterson talk contribs uploaded File:Test msg list.png
- 19:41, 16 July 2024 Thomas Peterson talk contribs created page File:Single Cyl Drop.png
- 19:41, 16 July 2024 Thomas Peterson talk contribs uploaded File:Single Cyl Drop.png
- 19:39, 16 July 2024 Thomas Peterson talk contribs created page File:SparkGraph.png
- 19:39, 16 July 2024 Thomas Peterson talk contribs uploaded File:SparkGraph.png
- 19:25, 16 July 2024 Thomas Peterson talk contribs uploaded a new version of File:Gov-pd-wiring.png
- 17:15, 2 July 2024 Thomas Peterson talk contribs created page EDR Troubleshooting - Engine data issues (Created page with "Symptom: There is missing engine data on the site but compressor data is working ==Verify Wiring== 1. The EDR will have wires from pin 9,10 of the module to the pink and purple wires in the CAT panel (A3 only) 2. The EDR will have wires from pin 13, 14 of the module to the green and yellow wires in the CAT panel Verify CAN termination 3. There is a CAN termination switch next to pin 14 of the EDR. If this is ON (to outside of module) then the CAT termination resistor...")
- 17:11, 2 July 2024 Thomas Peterson talk contribs created page EDR Troubleshooting - Incorrect Compressor Data (Created page with "Symptom: Some data from the compressor is showing up on the site, but some data is missing or incorrect ==Alter port timings== 1. Connect to the wifi terminal. Directions are in Appendix A. 2. In some cases, increasing some port delays can help with communications a. In the wifi terminal under the “Modbus Master” tab, open the heading “Port Timings” b. Increase the Write Delay Us to 50,000 c. Increase the Read delay Us to 4,000 ==Check Base Configuration==...")
- 17:10, 2 July 2024 Thomas Peterson talk contribs created page EDR Troubleshooting - Incorrect callout descriptions (Created page with "Symptom: Callouts are being sent normally but the description is not correct '''Verify Fault Code Table''' 1. Connect to the EDR wifi console. Instructions can be found here: EDR Wi-Fi Console 2. Go to the “Alerts” tab of the console 3. Open the “Shutdown Code” table 4. Edit the table to match the panel a. For TTD or DD40, this table should match the shutdown legend exactly b. For a DE3000, this table will match the channel list c. For a centurion, th...")
- 17:06, 2 July 2024 Thomas Peterson talk contribs created page EDR Troubleshooting - Missing Compressor Data (Created page with "Symptom: On the Connect site there is no compressor data (e.g. Annunciator Run Code, Suction Pressure, etc.), or on the Wifi console there are expected data items with a timeout of “Never”. ==Note that some values may not be present== 1. For a TTD or DD40, there won’t be any process pressures or temperatures (though there can be temperatures if a TDXM or DSM are set up). The Run Status and Fault Code should still show up though. ==Check EDR Port Setup== 2. Unde...")
- 16:46, 2 July 2024 Thomas Peterson talk contribs created page File:Comm timeout.png
- 16:46, 2 July 2024 Thomas Peterson talk contribs uploaded File:Comm timeout.png
- 14:08, 20 June 2024 Thomas Peterson talk contribs created page File:Edr test Sw.jpg
- 14:08, 20 June 2024 Thomas Peterson talk contribs uploaded File:Edr test Sw.jpg
- 14:02, 20 June 2024 Thomas Peterson talk contribs created page File:Dct test sw.jpg
- 14:02, 20 June 2024 Thomas Peterson talk contribs uploaded File:Dct test sw.jpg
- 22:06, 19 June 2024 Thomas Peterson talk contribs created page Checking for Test Software (Created page with "If a module has manufacturing test software installed or test mode active, it won't work normally. This page shows how to verify if normal software is installed. '''AFRC''' If the hardware ID ends in a "1", it is test software. If it ends in another number, it is normal software. '''DCT''' The DCT boots to a test mode if an internal switch is in a specific setting. To get it out of test mode, remove the back cover and switch the 4pin dip switch to all OFF. '''EDR'''...")
- 21:13, 11 June 2024 Thomas Peterson talk contribs created page File:Callout summary.png
- 21:13, 11 June 2024 Thomas Peterson talk contribs uploaded File:Callout summary.png
- 20:16, 10 June 2024 Thomas Peterson talk contribs created page File:Ecu thr.png
- 20:16, 10 June 2024 Thomas Peterson talk contribs uploaded File:Ecu thr.png
- 19:59, 10 June 2024 Thomas Peterson talk contribs created page File:Ecu hall 330x.png
- 19:59, 10 June 2024 Thomas Peterson talk contribs uploaded File:Ecu hall 330x.png
- 19:51, 10 June 2024 Thomas Peterson talk contribs created page File:Ecu fw mpu.png
- 19:51, 10 June 2024 Thomas Peterson talk contribs uploaded File:Ecu fw mpu.png
- 15:32, 7 June 2024 Thomas Peterson talk contribs created page Software Change Log (Created page with "This page shows major changes for software updates, sorted by module. ==DCT== ''' 1.66 - Not yet released ''' #Added standby timer adjustment, req brain 3096, found under Brain Misc Settings #Added some new brain digital output functions #Added TCP/Modbus to VFD connection framework. Currently testing on MV1000 drives. #Add commissioning report under "Information" #Add ECU pct load as a speed control option, requires latest Brain and EDT #Added compressor ratio per al...")
- 15:06, 7 June 2024 Thomas Peterson talk contribs created page Main Bearing Deviation Alarm (Created page with "==Overview== The "Main Bearing Temp Deviation" is a special built-in alarm that monitors for main bearing temperatures that deviate from the rest of the main bearing temps. To use, the Brain must be updated to v3111 or higher, and the DCT must be updated to 1.65.340 or higher. ==Enabling the Alarm== First, the thermocouple inputs for main bearings have to be enabled. These are set up as normal thermocouple inputs and can use any normal high kill alarm, but be sure t...")
- 15:05, 7 June 2024 Thomas Peterson talk contribs created page File:Mbdev alarm.png
- 15:05, 7 June 2024 Thomas Peterson talk contribs uploaded File:Mbdev alarm.png
- 15:00, 7 June 2024 Thomas Peterson talk contribs created page File:Mbdev alarmset.png
- 15:00, 7 June 2024 Thomas Peterson talk contribs uploaded File:Mbdev alarmset.png
- 13:25, 6 June 2024 Thomas Peterson talk contribs created page Back Activation (Created page with "In most cases when a device is activated a message is sent from the server to the device telling it to change its send settings. In some cases though the message can't be sent at the time, and a manual step is needed top pull the setting update in the other direction. An example case would be where a unit is set to active before the panel is powered up, and later it is powered and needs to be activated. The following shows how to request a service level update on a DCT...")
- 13:25, 6 June 2024 Thomas Peterson talk contribs created page File:Edr sync.png
- 13:25, 6 June 2024 Thomas Peterson talk contribs uploaded File:Edr sync.png
- 13:24, 6 June 2024 Thomas Peterson talk contribs created page File:Edr debug.png
- 13:24, 6 June 2024 Thomas Peterson talk contribs uploaded File:Edr debug.png
- 13:20, 6 June 2024 Thomas Peterson talk contribs created page File:Svc update.png
- 13:20, 6 June 2024 Thomas Peterson talk contribs uploaded File:Svc update.png
- 13:17, 6 June 2024 Thomas Peterson talk contribs created page File:System tel.png
- 13:17, 6 June 2024 Thomas Peterson talk contribs uploaded File:System tel.png
- 13:17, 6 June 2024 Thomas Peterson talk contribs created page File:DCT Settings Ssytem.png
- 13:17, 6 June 2024 Thomas Peterson talk contribs uploaded File:DCT Settings Ssytem.png
- 19:09, 27 March 2024 Thomas Peterson talk contribs created page File:Edt.jpg
- 19:09, 27 March 2024 Thomas Peterson talk contribs uploaded File:Edt.jpg
- 19:59, 13 March 2024 Thomas Peterson talk contribs created page EDT stand alone table (Created page with "The EDT module (20350) can be used in a stand alone capacity to translate engine data to modbus without use of an EMIT screen. The Modbus list is found here: [https://drive.google.com/file/d/12hMzQQbGhOkUW418gLoFQXhgKTfeQOfM/view?usp=sharing]")
- 17:31, 16 February 2024 Thomas Peterson talk contribs created page Waukesha VHP Engine Controls (Created page with "== Overview == EMIT engine control products (AFRC, Ignition, and speed controller) can be used on Waukesha VHP engines of various types. These kits can replace the ESM or upgrade older engines. This page covers ordering, install, and operating information. == Ordering Information == The sections below show what AFRC, Ignition, and governor kit would be selected for different applications, and the item numbers for spare parts. === AFRC === Note that the kit item numb...")
- 20:16, 15 February 2024 Thomas Peterson talk contribs created page File:Edt esm.PNG
- 20:16, 15 February 2024 Thomas Peterson talk contribs uploaded File:Edt esm.PNG
- 18:19, 15 February 2024 Thomas Peterson talk contribs created page Panel to ESM(r) Interfacing (Created page with "== Overview == The Waukesha ESM (r) is an engine control unit made by Waukesha for their VHP series engines. When a unit with an ESM is connected to an EMIT panel, the panel will use a few signals to control the start, stop, and speed of the engine. Many concepts are similar to connecting to other engines. === Initial Setup === Navigate to Settings - Brain - Outputs Setup - ECU Selection, and select "Waukesha ESM". == Panel to ESM Connections == There are three disc...")
