New pages
From EMIT Controls
- 16:48, 11 November 2024 Engine Pre-Lube Monitor (hist | edit) [2,186 bytes] Thomas Peterson (talk | contribs) (Created page with "==Background== In some cases the EMIT panel handles both engine pre-lube and compressor pre-lube, such as if there is not a 3rd party ECU. More commonly the EMIT panel will handle the compressor pre-lube process and the engine ECU (e.g. CAT ADEM) handles the engine pre-lube. This article only applies to the case where the EMIT panel does not run the engine pre-lube. As part of the start sequence after the compressor pre-lube completes the EMIT panel signals the engine...")
- 21:02, 23 October 2024 Digital Input Cycle and Time Monitor (hist | edit) [1,937 bytes] Thomas Peterson (talk | contribs) (Created page with "==Overview== Starting with DCT v1.67.464 and Brain v3244 the system has the ability to monitor the cycle history of up to three digital inputs. The system will accumulate the number of cycles and the total amount of time asserted (either closed to ground or open). This is commonly used to track dump valves. This is similar to No-Flow monitoring, but does not include an alarm to shut down the unit. If a lubrication cycle alarm is needed, see No Flow (pulse) Inputs...")
- 16:23, 8 October 2024 Brain battery saver output (hist | edit) [3,153 bytes] Thomas Peterson (talk | contribs) (Created page with "==Overview== ASD")
- 19:14, 27 September 2024 Config Change Emails (hist | edit) [1,697 bytes] Cvalentine (talk | contribs) (Created page with "==Overview== Config changes are logged and notification emails are sent to a list of contacts for the area. ==Sign Up for emails== Go to the Areas page. border|700px|alt=Image showing where to edit the config change contacts list Select the contacts you would like to have subscribed. border|700px|alt=Image showing where to edit the config change contacts list If the contacts are not found, go to Portal...") Tag: Visual edit: Switched
- 17:21, 27 September 2024 Region Passwords (hist | edit) [2,218 bytes] Cvalentine (talk | contribs) (Created page with "==Overview== Region Passwords are available to remotely set passwords on DCTs. Simply set the password for an entire region and a message will automatically be sent to all the units in the region to update their password. A passwords page is available to easily search and find the actual password for each unit. ==Creating Password== Go to the Areas Page border|700px|alt=Image highlighting the link to the areas page|Go to areas page Go to t...")
- 20:23, 4 September 2024 Connecting Ignition to a DetCon (hist | edit) [5,059 bytes] Thomas Peterson (talk | contribs) (Created page with "==Overview== The EMIT ignition system can be linked to a MotorTech (TM) DetCon controller, and the data from the DetCon can be used to retard individual cylinder timings of the ignition. This page describes how to set up and use this feature. ==Installation== Install the DetCon as specified in the Motortech instructions. Important notes and clarifications: #The knock sensors are wired in '''firing''' order. The "Sensor 1" input on the Detcon will wire to the knock se...")
- 19:51, 15 August 2024 Standby start or Unexpected start fault (hist | edit) [1,370 bytes] Thomas Peterson (talk | contribs) (Created page with "In Brain v3180 a new built-in fault was added for an unexpected engine start. This logic will trip if the rpm goes above crank terminate for more than 1/2 second while the panel is in standby. ==Logic== In a normal startup on a CAT engine, the sequence will be: #Operator presses RESET button #EMIT panel goes to STANDBY and the DRIVEN EQUIPMENT READY output turns on (goes clear) #The CAT panel can be cleared of all alarms #(If switch present and not previously set) CAT...")
